Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Kingwood Homeowners
Masonry cracks spread faster than most homeowners expect. In Kingwood‘s humid climate, a hairline crack in the crown or a soft patch of mortar at the shoulder lets water into the brick, and by the time a stain shows up on the firebox, the damage has usually been working for a season or two. Our technicians have up to 8 years of experience, and they diagnose the whole system before anyone quotes a repair: crown, flashing, flue, firebox. We use the materials the industry trusts, which means you get the right fix for the actual failure instead of a patch that washes out in a year. Call (844) 960-2344 and we’ll book a repair visit. We answer 24/7, and same-day visits are often available.

What Our Chimney Repair Service Includes
Chimney repair covers every structural and water-shedding piece of the system above and around the firebox. We handle six repair categories under one scope, so a cracked crown and a damaged flue don’t turn into two contracts with two contractors.
Mortar Repointing
Joins between bricks take the worst of the weather and are the first thing to go soft. When the mortar rakes out and crumbles, the brick above it starts to shift. We cut the failed joints back to solid material and repack them with a mortar matched to your chimney’s existing brick, so the repair moves with the wall rather than cracking away from it.
Spalling Brick Repair
Spalling is brick face flaking off in sheets, and it almost always traces back to water getting in and pushing out through the brick. One bad brick in a run can shed pieces that block the flue or hold moisture against the ones beside it. We remove the broken units, match replacements to the surrounding brick, and correct the moisture path that caused the failure so it doesn’t just recur on the next course up.
Chimney Waterproofing
A chimney wicks water through the brick and mortar, not just from the top, and that is the root of most chimney repair in this part of Texas. After any masonry work has cured, we apply a breathable vapor-permeable waterproofing so moisture inside the chimney can escape while windblown rain is shed off the surface. Sealing a damp chimney too soon traps the water and makes the problem worse, which is why the timing matters.
Flashing Repair
Flashing is the metal that seals the joint where the chimney meets the roof, and it’s the spot most roof leaks get blamed on the shingles. Failed flashing, rusted step flashing, or a loose counter-flashing lets water run straight down into the attic and ceiling. We re-bed, reseal, or replace the flashing assembly and tie it back into the roof covering so the joint sheds water the way it should.
Chimney Rebuilding
When the top of a chimney is too far gone to repoint or patch, the section above the roofline gets rebuilt. We take it down to sound courses, rebuild the stack with proper flue clearances, and crown it so water runs away from the flue rather than pooling against it. This is the repair that restores a leaning or badly degraded chimney, and we handle it as a single scope rather than handing the crown and the flue off separately.
Tuckpointing
Tuckpointing is the finish pass that gives repointed joints a clean, uniform look and it’s often the last step on a brick repair. We strike the joints consistently, match the new mortar to the existing color and profile, and make sure the repair reads as part of the chimney rather than a patch. It matters on the visible faces of the stack, where a mismatched joint draws the eye and hints at sloppy work.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We work with Gelco and Olympia Chimney on the flue side, and both come up most often when a liner has to be replaced or restored as part of a repair. Gelco liner components are something we install regularly, and we know how their joints and terminations need to be seated so the flue stays sealed at the top. Olympia Chimney systems show up on a lot of the older flues around Kingwood, and we’ve learned where they hold up and where they tend to fail after years of heat cycling.
On the masonry and cap side, Famco and Copperfield come into play for caps, dampers, and top-of-chimney components that have to survive our summer heat and the occasional hard rain. We don’t claim to be a dealer and we don’t stock parts, but we work with these brands often enough to source and fit them correctly. Whether you have Gelco, Olympia Chimney, Famco, Copperfield, or any other make on your chimney, we can help.
Signs You Need Chimney Repair Right Now
- Cracked or crumbling mortar between the bricks. If you can dig a fingernail into a joint and pull material away, the mortar has failed and the bricks above it are being asked to carry load they weren’t meant to. Left alone, that leads to a leaning stack.
- Brick flakes on the roof or in the gutters. Spalled brick means water has gotten inside the masonry and is pushing the face off from behind. The pieces themselves can also block the flue or hold moisture against neighboring brick.
- Water stains on the ceiling or firebox walls. A stain around the chimney chase or a dark ring inside the firebox usually points to flashing or crown failure. Water and masonry don’t mix, and an active leak gets worse every time it rains.
- A visible lean or separation at the roofline. A chimney that’s pulling away from the house or tilting at the top is a structural problem, not a cosmetic one. Stop using the fireplace and get it inspected before the next burn.
- A damaged or missing chimney cap. A loose cap lets rain in, invites birds and squirrels, and can let sparks land on the roof. A cap replacement is one of the least expensive fixes we do and one of the most protective.
Our Chimney Repair Process – Step by Step
We diagnose before we quote. That’s the whole method, and it’s why our estimates hold up.

- 1
Inspection and photo report. We look at the full system, crown to firebox, and photograph what we find. You see the same images the technician works from, so the recommendation isn’t something you have to take on faith.
- 2
A written scope and flat price. We put the repair in writing before anyone starts: the materials, the method, and the price for the job. If a repair can safely wait, we tell you that instead of selling it today.
- 3
Material selection for your flue. Every flue is different, which is why we carry DuraFlex flexible liner systems for the non-straight and aged configurations that a rigid liner won’t pass. We also have HeatShield ceramic resurfacing available, which restores a damaged flue from the inside rather than replacing it in full.
- 4
The repair, done in one scope. Masonry, cap, crown, flashing, and liner work all get handled under one call. That’s the advantage of single-company accountability: no contractor waiting on another contractor before the job can close.
- 5
Final check and walkthrough. We verify the flue pulls draft correctly, the crown sheds water away from the opening, and the flashing is watertight. Then we walk you through what changed and note anything to watch.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Kingwood?
Chimney repair in Kingwood typically runs from about $250 for a small mortar or cap repair up to several thousand dollars for a rebuild above the roofline, and the estimate sets the final price. Here’s roughly where the common jobs land:
| Repair | Typical estimated range |
|---|---|
| Mortar repointing (single area) | $250 – $600 |
| Flashing repair | $300 – $700 |
| Chimney cap replacement | $250 – $500 |
| Waterproofing application | $350 – $800 |
| Spalling brick repair | $500 – $1,500 |
| Crown rebuild or replacement | $500 – $1,200 |
| HeatShield flue resurfacing | $1,200 – $2,500 |
| DuraFlex flexible liner installation | $1,500 – $3,500 |
| Chimney rebuild above the roofline | $3,000 – $8,000 |
What moves the price: how high the work is, how far the damage extends, whether a repair can be resurfaced instead of replaced, and the material you choose. HeatShield often costs less than a full reline, and a liner chosen for your flue’s actual size and shape protects against overspending on a system that doesn’t need to be bigger than the firebox calls for. The free estimate covers a full inspection and a photo report, and any flue repair we recommend is backed by what you see in the photos. If the chimney isn’t leaking and the mortar is sound, we’ll tell you that too. Call (844) 960-2344 for an exact quote.
Chimney Repair Near Kingwood – Our Service Area
We take chimney repair work across Kingwood and the surrounding communities, including Humble, Atascocita, Spring, Porter Heights, Woodbranch, Lake Houston, Greenspoint, Dayton, Acres Homes, Champions, and Crosby. Response time depends on the day’s schedule; call and we’ll tell you the earliest opening. Homeowners in Humble can reach us the same way, and if you’re near Atascocita, our chimney repair service covers that side of Lake Houston. From a standing cap to a rebuild above the roofline, one call covers the whole scope.
Serving Kingwood, TX – Our Local Coverage Area
We serve Kingwood and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Kingwood
Chimney repair is the structural work on a chimney beyond routine cleaning: fixing cracked mortar, replacing spalled brick, repairing flashing and crowns, and restoring or relining the flue. It includes resurfacing a damaged flue with HeatShield where a full liner isn’t necessary, and rebuilding the top of the stack when the masonry has failed past patching. It’s distinct from chimney sweeping, which is cleaning, and from inspection, which is diagnosis. Call (844) 960-2344 if you’re not sure which one you need.
Most small repairs, like a cap replacement or a single area of repointing, are done in a day. Flashing repair and waterproofing are also usually one visit, though waterproofing needs the masonry to be dry before it goes on. A full reline or a rebuild above the roofline takes longer, sometimes a few days, because the flue needs to be clear and the crown rebuilt in stages. Call (844) 960-2344 and we’ll give a timeline with your written estimate.
A small mortar or cap repair typically starts around $250, while flashings run $300 – $700 and a rebuild above the roofline can reach several thousand. The price depends on how much of the chimney has failed, whether the flue needs resurfacing or a new liner, and how high the work is. The estimate is free and the written price sets the final cost, so there are no surprises after the fact. Call (844) 960-2344 for an exact quote.
Yes, we work with Gelco and Olympia Chimney systems regularly. Both come up when a flue needs a new liner or a repair around an existing one, and we know how their components need to be fitted so the flue stays sealed at the top. We also work with Famco, Copperfield, DuraFlex, and HeatShield, so a repair on an existing liner doesn’t automatically mean a full replacement. Call (844) 960-2344 to book a diagnostic visit.
Same-day visits are often available, and we book repairs as quickly as the schedule allows. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed on Saturday. A call outside dispatch hours is booked into the next opening. The one thing we won’t do is rush a diagnosis, because the wrong repair costs more than the right one. Call (844) 960-2344 and we’ll find you the earliest slot.
You see the photos. Every repair recommendation comes with a photo report and a written scope, so you’re not taking a stranger’s word for it that the liner is shot. We also tell you plainly when work can safely wait, because not every crack or stain demands action this month. The estimate is free and the price is flat per job. Call (844) 960-2344 if you want a second opinion on a quote you’ve already received.
Clear the hearth and the floor in front of the fireplace, and move anything breakable away from the base. Make sure we can get to the roof and the attic access if the repair involves flashing or the stack above the roofline. If you’ve noticed a leak, note where and when it shows up, since that helps the technician trace it. That’s about it. Call (844) 960-2344 to schedule, and we’ll confirm what to expect.
Schedule Your Chimney Repair Service in Kingwood Today
If you’re seeing crumbling mortar, spalling brick, a water stain, or a cap that’s seen better days, the repair gets cheaper the sooner it’s diagnosed. Call Chimney Sweep Kingwood at (844) 960-2344 for a free estimate with a photo report and a written scope. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed on Saturday. You’ll know what your chimney actually needs, and what it doesn’t, before anyone picks up a trowel.
Written by the team at Chimney Sweep Kingwood.