Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Cap & Crown Across Greenspoint
If you own or manage a fireplace in Greenspoint, you’re probably dealing with short metal chimney stacks rather than tall masonry ones, and that changes what a cap and crown job involves. Most of our cap and crown work in Greenspoint happens on 1970s and 1980s prefab fireplaces, not on older brick chimneys, so we plan each job around thin flues, tight roof space, and the way rain and humidity get into a factory-built stack. Call (844) 960-2344 and we’ll set a time to look at it. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Greenspoint Homeowners Call Chimney Sweep Kingwood for Chimney Cap & Crown
We serve Greenspoint regularly, and the local pattern is hard to miss. Around 77060, off Greenspoint Drive and the Beltway, the housing is mostly dense multifamily: garden-style apartments, townhomes, and small patio-home subdivisions built with factory-made fireboxes and short chimney stacks. That’s a different kind of cap-and-crown work than a single masonry house, and we plan for it.
Our technicians have up to 8 years of experience, and they’re used to reading a property rather than one roof. When we pull a cap and find rusted-through steel or a spalled crown on one stack, we know what we’re likely to see on the matching stacks nearby, because the same builder put them up in the same few years. That saves you the guesswork of wondering whether it’s just your unit. We work with the materials the industry trusts, including Gelco, Olympia Chimney, and Famco, and we carry the cap, crown, and liner scope in one company so there’s no handoff between contractors.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Cap & Crown Services in Greenspoint
For apartment owners, HOA boards, and townhome residents, the cap and crown side of a chimney is where water gets in or stays out. Here’s how those jobs go in Greenspoint.
Cap Installation
A new cap keeps rain, birds, and debris out of the flue while letting smoke escape. On Greenspoint’s short prefab stacks, the right fit matters more than the cap’s looks: a loosely fitted cap rattles or blows loose, and a low one can restrict draft. We measure the flue opening and set a cap that matches the stack, then confirm it’s seated properly before we leave the roof.

Cap Replacement
Builder-grade single-flue caps fail in bulk on these properties, and once one rusts through, the neighbors are usually close behind. We replace steel caps that have corroded or bent, and on a property with matching stacks we’ll walk the identical units so you’re not replacing them one call at a time. If the flue underneath is sound, a straight cap swap often solves the draft and water issue.

Crown Repair
The crown is the mortar cap on top of the chimney chase, and on 1970s prefab fireplaces around Greenspoint, it’s the part that cracks and spalls first. Once it opens up, Gulf Coast rain tracks down into the smoke chamber instead of shedding off the top. We repair the crown, rebuild the sloped top so water runs off, and check the chase cover and stack while we’re up there.

Crown Coating
A crown coating seals a crown that’s cracked but still structurally sound, so you don’t have to rebuild it. It’s a practical option on Greenspoint roofs where the crown has hairline cracks from years of sun and rain but hasn’t broken apart yet. We prep the surface and apply a flexible coating to keep water out, then tell you honestly if a coating is enough or if the crown needs rebuilding.
Trusted Brands We Service in Greenspoint
We work with professional-grade brands and know how each behaves on a Texas roof. HeatShield’s ceramic resurfacing system lets us restore a damaged liner rather than reline the whole flue, which is often the right call on an older prefab stack that’s cracked but not collapsed. Gelco, Olympia Chimney, and Famco caps and components are the kinds we install and replace because they hold up to humidity and sun. We don’t claim to stock parts locally; we spec and order what the job needs, so turnaround stays quick on a Greenspoint property with several stacks to fix. If your flue is complicated, we can source DuraFlex flexible liner systems for non-straight runs, and we’ll tell you whether the fix is a cap, a crown, or something deeper.
Common Chimney Cap & Crown Problems We See in Greenspoint Homes
The failures we run into here have less to do with heating than with water and age, and they don’t stay on one unit. These are the patterns we look for on a Greenspoint roof:
- Missing or rusted-through chase covers on short prefab stacks. The chase cover is a low metal lid on the chimney chase, and on 1970s and 1980s stacks it rusts through first, letting rain and humidity into thin metal flues. That accelerates creosote glaze and rust at the liner joints, so what starts as a leak becomes a flue problem.
- Original crowns that crack and spall. Builder-grade crowns on factory-built fireplaces in Greenspoint age out over decades of sun and rain, opening cracks that let water run down into the smoke chamber. On a townhome with a shared chase, that water can reach more than one flue.
- Caps failing in bulk across a property. Single-flue caps on these garden-style units were cheap to begin with and rust through together, so adjacent townhomes can end up drawing from a shared stack. When neighboring caps and shared flues aren’t pulling properly, cross-contamination shows up as smoke and odors in a unit that isn’t even using the fireplace.
- Nests and pest intrusion on unused stacks. The heating season is short here, so a Greenspoint fireplace can sit idle for months. Birds, wasps, and small animals move into an open flue, so pest screening and nest removal are as common on this side of Houston as actual sweeping.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Cap & Crown in Greenspoint, TX
Pricing here reflects the multifamily stock: lots of short metal stacks, often replaced in matching batches. A typical single-flue cap installation in Greenspoint runs $180 to $400, and a custom cap built for a wide or multi-flue stack runs $400 to $850. A crown repair is usually $300 to $700, and a crown coating runs $250 to $450. What moves you up or down the range is the stack count, roof access on a tight street, and whether you’re fixing one unit or several identical ones. The written estimate sets the final price, and the estimate itself is free. We don’t recommend new liner or masonry work unless the evidence on the roof supports it, and we’ll tell you plainly when a cap or crown repair can wait.
We Also Serve Cities Near Greenspoint
Greenspoint sits close to a lot of other neighborhoods, and we cover the surrounding areas for cap and crown work: Acres Homes, Champions, Humble, and Spring are all within range. If you’re just outside Greenspoint or manage a property that spans these cities, one call handles the whole scope through our chimney cap & crown team. Reach out and we’ll look at the property as a whole.
Serving Greenspoint, TX – Our Local Coverage Area
We serve Greenspoint and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Cap & Crown in Greenspoint
One inspection on a representative unit can tell you a lot, because these buildings went up together with the same prefab stacks. When we find a rusted chase cover or a failed cap on one stack, we expect to find the same defect on the matching stacks, so we can report what the property likely needs. We still inspect a sample across the property to confirm it, then price the job per unit. Call (844) 960-2344 for an exact quote – estimates are free.
They fail faster because they’re thin builder-grade steel and mortar on a short stack, exposed to Gulf Coast humidity and heavy spring and fall rain. The chase cover rusts through first, then the crown cracks from years of sun and rain, and water gets into the flue. The building’s age does the rest. A single failed stack usually means its neighbors are close behind. Call us to have the property looked at as a group.
Yes. When adjacent units share a stack or sit close together, a missing or failed cap on one side can let smoke and odors pull into a neighboring unit. That’s why proper caps and screened tops matter on a townhome even if your own fireplace is rarely used. We check shared and adjacent flues when we inspect, so the fix addresses the whole stack, not just your half of it.
They do, and it matters here because the heating season is short, so fireplaces sit open and idle for months. That’s plenty of time for birds, wasps, and small animals to move into the flue. A screened cap keeps them out. We install pest screening as part of a cap job. Call (844) 960-2344 for a free estimate and we’ll tell you what your stack needs.
Crown coating seals a cracked but structurally sound crown, while crown repair rebuilds a crown that has spalled or broken apart. On a 1970s prefab, we first check whether the crown just needs flexible coating or a proper rebuild, and whether the chase cover and stack need attention too. We recommend one over the other based on what we can see and show you. Call (844) 960-2344 – estimates are free.
Get Your Greenspoint Chimney Capped and Sealed
Whether you own one townhome or manage a whole Greenspoint property, the cap and crown are your chimney’s first line against water, pests, and shared-stack trouble. Call (844) 960-2344 for a free estimate. We answer 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday. We tell you what your chimney actually needs, from the first stack to the last.
Written by the team at Chimney Sweep Kingwood.