Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Sweep Across Crosby
Crosby chimneys take a beating from the sky, not just from the firebox. Wind-driven rain off the Gulf pushes past displaced caps and rusted chase covers, and a stained ceiling near the chimney is often the first sign a homeowner notices. We work with chimney sweep calls across Crosby that start as water-intrusion checks and end with a clean, sealed, code-compliant flue before the first cold night. Our technicians have up to 8 years of experience, and every visit starts with a camera inspection and a photo report you can see for yourself. Call (844) 960-2344. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Crosby Homeowners Call Chimney Sweep Kingwood for Chimney Sweep
Crosby is an unincorporated stretch of coastal prairie northeast of Houston, where new master-planned subdivisions sit next to older rural acreage along US-90 and FM 2100. That split shapes the work. In the newer builder-grade neighborhoods, most “chimneys” are prefab factory-built flue systems with thin metal chase covers and caps that a tropical storm can cock sideways. In the older single-story brick and siding homes on large lots, we’re usually looking at masonry fireboxes that have gone decades without service, with cracked crowns and failed flashing letting moisture into the brick.
That’s why Crosby homeowners call us instead of a generalist handyman. We diagnose the actual problem first, whether it’s a rusted-out cap, a leak path around the flashing, or a flue packed with glazed creosote, and we tell you what your chimney actually needs. Some calls are a routine annual sweep. Some are a Level 2 inspection after a storm. We don’t recommend liner or masonry work without camera evidence you can look at yourself.
Our technicians have up to 8 years of experience working with the materials the trade trusts, from Crosby subdivisions to the rural roads out toward Barrett. One call handles sweep, inspection, cap and crown, and repair, so there’s no juggling three contractors for one chimney.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Sweep Services in Crosby
Level 2 Inspection
In Crosby, a Level 2 inspection is usually the right starting point because the most common problem isn’t soot in the firebox, it’s water getting in somewhere. A Level 2 goes into the flue with a camera and checks the crown, cap, chase cover and flashing for the leak path. It’s also the inspection you want for a real-estate transaction or after a hurricane has moved through. You get a photo report, and nothing gets recommended without evidence you can see.

Creosote Removal
Crosby winters are short and fires are recreational rather than primary heat, so sweeping gets deferred for years. That’s exactly how first-degree creosote ages into glazed second- and third-degree creosote that a standard brush can’t touch. When we find glazed creosote in a Crosby flue, we explain the options and what a proper removal involves, and we say plainly when a job can safely wait until after the season. Removing it before it hardens saves you both money and risk.

Fireplace Cleaning
A full fireplace cleaning in Crosby includes soot removal from the firebox, smoke chamber and damper, plus a check on the refractory panels in prefab units. In newer subdivisions with factory-built fireplaces, we check that the chase cover isn’t rusted through and that the cap is still seated after wind. In older masonry fireboxes, we look for spalling brick and moisture that never dries out between the handful of cold nights Crosby actually burns.

Soot Removal
Soot builds unevenly in a lightly used fireplace: heavy after a few storm-season power-outage burns, thin otherwise. We remove it without scattering it through the living room, using drop cloths and a sealed vacuum. It’s a small job on its own, and it’s part of every annual sweep we do across Crosby.
Trusted Brands We Service in Crosby
We work with the materials the industry trusts. That means DuraFlex flexible liner systems for complex or aged flue configurations, HeatShield ceramic resurfacing for damaged flues that can be restored rather than fully relined, and Olympia Chimney and Gelco components for caps and liner work. In Crosby’s mix of prefab and aging masonry, having the right material for the flue matters more than a one-size-fits-all kit. We carry no parts stock and make no warehouse claims; we source the correct component for your chimney and install it as a single accountable job from inspection through repair.
See the difference
Before
After
Before
After
Before
AfterCommon Chimney Sweep Problems We See in Crosby Homes
- Displaced or rusted-through caps and chase covers. Wind-driven rain from tropical storms gets past a cap that’s cocked sideways or a chase cover that’s rusted through, so water runs down the flue and shows up as a ceiling or attic stain instead of an obvious fire problem. That’s why most Crosby sweep calls start with water, not smoke.
- Hairline-cracked masonry crowns and failed step flashing. After a storm, a cracked crown or failed flashing lets moisture into the masonry, causing spalling brick and damp creosote that never dries out between the few cold nights Crosby actually burns. Inspections here routinely double as water-intrusion checks.
- Glazed creosote in lightly used fireplaces. Builder-grade prefab fireplaces in newer subdivisions go unswept for years because residents burn recreationally, letting first-degree creosote glaze into second- or third-degree creosote that a standard brush can’t remove. A camera inspection tells you which stage you’re dealing with.
- Blocked flues and backdraft on the first cold night. A nest, soot load or debris can block the flue so smoke rolls back into the room when the fireplace is lit for the first time in months. This is a blockage or draft problem you want checked before you light up, not after.
Pricing for Chimney Sweep in Crosby, TX
Straight answers on cost, because you deserve to know before you book. A typical annual sweep and Level 1 inspection in Crosby runs about $150 to $275. A Level 2 inspection with a camera runs about $225 to $400. Creosote removal beyond a standard sweep, especially for glazed second- or third-degree creosote, typically runs $300 to $900 depending on how much build-up there is. A cap and crown repair or replacement, which is often the real fix for a leak, usually runs $250 to $700. All of these are estimates for Crosby’s market, and the written estimate sets the final price. The estimate itself is free, and you always see the photos before any work is agreed.
We Also Serve Cities Near Crosby
We work the same coastal-prairie and lake-edge neighborhoods around Crosby, including Barrett, Atascocita, Lake Houston and Humble. If your chimney is on that side of the metro and you’re weighing a storm-season check against waiting, call us and we’ll tell you where you stand. One call, complete chimney care, from the lake to the rural roads out toward Barrett.
Serving Crosby, TX – Our Local Coverage Area
We serve Crosby and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Sweep in Crosby
A ceiling or attic stain near the chimney after rain almost always means water is getting past the cap, chase cover or flashing, not that the firebox itself is failing. In Crosby’s storm exposure, a cocked cap or rusted chase cover lets wind-driven rain run down the flue. We trace the leak path with a camera inspection and photo report so you can see exactly where it’s coming from before any repair is agreed.
Yes. Light use is exactly why creosote glazes in Crosby: fires are recreational, so first-degree creosote sits for years and ages into second- or third-degree deposits a brush can’t touch. Annual sweeps catch it early. Even on a rarely used prefab, the cap and chase cover need a look after storm season.
First-degree creosote is light soot and flaky deposits a standard brush removes easily; second-degree is stickier and harder to clear; third-degree is glazed and baked on, and a brush won’t touch it. It matters in Crosby because lightly used fireplaces defer sweeping, letting first-degree age into glazed deposits that need a proper removal. A camera inspection tells you which stage you’re dealing with and whether anything needs to happen now.
Start with the cap and chase cover, then the crown and flashing. Storm winds displace or bend caps and rust eats through thin chase covers; cracked crowns and failed step flashing let water into the masonry and show up later as spalling brick or a damp smoke chamber. A post-storm Level 2 inspection is the fastest way to find the leak path before it spreads.
It can be either, and only an inspection tells you which. A nest, heavy soot load or fallen debris can block the flue and force smoke into the room; a cold, wet flue with a cracked crown can also fail to draw. We check the flue with a camera and check the top-end conditions so we can tell you whether it’s a blockage to clear or a draft problem to fix.
Before the first fire of the season, or after the next storm rolls through, get a real diagnosis instead of a guess. Call (844) 960-2344 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Every recommendation comes with a camera inspection and photo report, and we’ll tell you plainly when work can safely wait.
Written by the team at Chimney Sweep Kingwood.